Version History & Release Notes
Updated 3 days ago
This article provides the version history, release notes, and changelogs for all MixWave drum libraries. Click on a product name below to view its updates and changes.
Initial Release
Added
Lock mapping between snapshot changes
Drum and Cymbal details in Kit View dropdown menus
Support for MIDI channel aftertouch as the Hi-Hat controller
Support for triggering manual chokes via polyphonic aftertouch
Comp, EQ & Tape labels added to Master Panel
Fixed
Clicking artifact in Rack Tom 1 VL10 RR6 Close Mic Mixed and Unmixed samples
Envelope functionality for certain Close Mic groups
Issue with release-triggered articulations
User mapping stored as the last one used when choosing "Save as User Mapping"
Output routing not being reapplied when loading Snapshots
Automation name setup (incorrect counter for Width vs Pan)
Improved
Adjusted sample start time on all Rack Tom 1, Rack Tom 2, and Floor Tom VL10 Mixed and Unmixed samples
"MIDI CC TRIGGER" articulation renamed to "MIDI CC"
"Pedal Chick" articulation name changed to "Pedal Closed"
"Pedal Splash" articulation name changed to "Pedal Open"
"Hi-Hat CC" on Hi-Hat velocity settings panel renamed to "Hi-Hat Control"
Fixed
Disabled accidentally enabled developer mode
Added
Babar, Timbale High and Timbale Low samples
Fixed
Noise on Kick room mixed samples
Noise on various overhead and room samples for Brass Snare
Noise on various room mixed samples for Wood Snare
Noise on room samples for Rack Tom 1, 2 and Floor Tom (hit/rim), and Stick clicks
Behavior of solo and mute with Snare and Snare Shimmer reverb channels
Kit View trigger animations get stuck on purged kit pieces
Kit View trigger animations sometimes showing even when Preview function is disabled on Settings page
Kit View tab button is partially unclickable
Boost switch remained enabled when disabling Mixed switch and Link was activated
Updated
General MIDI mapping (mapped Plate hit articulation to G#2)
Snapshot 03 Tight Kit room sub channel, volumes set to 0 dB
Snapshot 07 Roomy Kit Crash 1 & 2, Rack Tom 1, Rack Tom 2, Floor Tom & Sticks Room mic volumes
Snapshot 11 Fast And Metal room sub channel volumes set to 0 dB
Zone volumes adjusted for Rack Tom 1, 2 and Floor Tom hit/rim close mic
Behavior of Tune knob is more logical across the board
Improved
Added warning when audio engine is not running
Initial Release
Initial Release
Initial Release
Initial Release
Initial Release
Initial Release
Initial Release
Added
Mix control for the master compressor effect
Changed
Clicking on hi-hat on Kit View now triggers Open 2 articulation instead of Edge Tight articulation
"Route all channels to sequential outputs" option now skips Mixer channels that are not used
Added MIDI CC trigger articulation assignment to Default, General MIDI, EZD and SD MIDI mappings
Improved
Choke group muting behavior (i.e. on hi-hats) when playing a soft hit after a harder one, room mic now has a longer choke fade out time
Fixed
Splash and China cymbals had their names swapped by mistake in Kit View dropdown
Tip and Edge articulations of Stack and Junk Hat cymbals were swapped by mistake on Settings page
Adjusting the envelope parameters didn't adjust the envelope for Mixed close mic groups
Script warning that appears when using the MIDI learn functionality on Settings page
Master volume slider reporting the unit as DB instead of dB
L-R Flip not affecting any mixer channels except Overhead and Room
Mixed/Boost/Tune controls didn't work correctly for alternate snares
Inconsistent or no sample playback in certain combinations of Mix and Boost switches between kick, snare, overhead and room channels (to fully apply this fix, reloading Thomas Pridgen Drums.nki is required!)
Close mic envelope parameters were adjusted when individual sub-mixer channels were selected. Now they will only be adjusted when the envelope panel is set to ALL
Initial Release
Initial Release
Initial Release
Initial Release